ouki 发表于 2011-9-30 00:18:12

Cisco出狠招-新版Lab和TS 考一个挂一个

听说从八月底九月初开始Cisco 逐渐推出了新版的TS3++和config lab. 新版lab没有Frame-relay。有Pfr/OER, MST, WCCP, Ipv6... 题量和难度增大很多，我所知道的战友全都被挂。怪不得最近的战报很少呢。版主大人和隐居大虾，请帮忙找找题库吧。{:soso_e109:}


疯狂的尼采 发表于 2011-9-30 00:36:55

{:soso_e126:}

chenchen9527 发表于 2011-9-30 00:58:10

不会吧，那我等有新题库了再考

半夏微光 发表于 2011-9-30 01:08:22

这让我情何以堪啊!

jphh1314 发表于 2011-9-30 08:20:49

{:6_269:}

zoom123 发表于 2011-9-30 09:11:45

{:6_283:}

jordan2011 发表于 2011-9-30 09:14:46

{:6_265:}

NSTcisco 发表于 2011-9-30 10:44:25

改吧，改吧，中国人就是为考试而生的
祝大家都能顺利通过。
努力，努力，再努力~~

Thinklab李 发表于 2011-9-30 11:41:36

我们9月份连考三个，PASS三个 ，Cisco太给力了啊！

Brooke 发表于 2011-9-30 12:07:03

{:6_291:} 看见蟑螂我不怕不怕啦

skymobi 发表于 2011-9-30 12:58:52

已经刚变过题，过段时间应该就稳定了

wanzxj 发表于 2011-10-1 00:40:24

TS3++ solution：

1) R15 cannot telnet R14 & R13 while sourcing loopacbk zero( fram relay question)
R13
interface Serial0/0
frame-relay map ip 172.16.13.1 341 broadcast
frame-relay map ip 172.16.13.3 345 broadcast

2) Ensure the output of show standby on R22 and R23 is the same as show below
   track 1 is shut down remove it
   missinf preemtion on r23
   R22 is not nessary to confing preempt
   priority on r22 is 150 and R23 is 100

3) R24 cannot telnet or pi g r29 192.168.20.1 fix it
   chap authentication bet R25 and R29
   R25 ask for authentication without username
   ensure password is the same on both side

4) pc 10.1.1.20 on R20 cannt teolnet or ping pc 10.1.1.28on R28 fix it
   R8 is ASBR all bgp route from as300 need to redistribute into ospf and flood into R20
   ensure ospf route also redistributed into bgp on R8

5) R28 must see two next hop with network 1.100.100.100 in show ip bgp table
   on r6 add r8 as route-relfector client
   on r26 add next hop self to r28
   on 27 add bgp default local-preference 200

6) Ensure R13 can ping multicast group 224.8.8.8 in AS 200
   r1 r2 r3 r5 r6 r7 r8 r9 r11 are running multicasst and in sparse-dense mode
   ensure r3 is the rp in as100 and r8 is rp in as200
   R3 and R8 running MDSP ensure they can access each oter so that can exchange source
   information
R1
router bgp 100
redistribute ospf 1 metric 20
router ospf 1
redistribute bgp 100 subnets
R3
ip msdp peer 10.1.1.8 connect-source loopback0 remote-as 200

7) R1 can not telnet R4 ipv6 ADDRESS 2011:abc:43::4 ,fix the problem
   ipv6 ospf is down between R1 and R3
   R1 R2 R3 R4 are running ospfv3 area 0
   r1 should can ping r4 ipv6 unicast address not r2
   on r3 there is an acl(traffic-filter) pls remove it or allow it

8) R13 can not sync with r5 pls fix it
   note:-r3 get the time from r5 thr' ntp
   ensure there is not acl blocking ntp traffic udp port 123
   check authentication

9) switching
fix sw2 so that sw2 is the root for mst 1,cannot change any config in sw1
note: the layer 2 traffic from r9 to R10 should goto sw1 and sw2
common preconfiguration
SW1, SW2
spanning-tree mst configuration
name cisco
instance 1 vlan 109 121
insnce 2 vlan 112 119
SW1
spanning tree mst 2 root pri
SW2
spanning-tree mst 1 root pri
change port priority on the interfCE
Interface F0/X ( THE PORT CONNECTED TO VLAN 109 AND 121)
spanning-tree-mst 1 port-priority 0

10) ZONE BASE FIREWALL
   r30 cannot not telnet r31 fix it
   note:-
   on r29 is configured as zone base firewall
   remove match all statement in class map type inspect or change it to match-any
   ensure ther is not acl or the acl match ip right ip address in the exam
   Also the IP address on R31 is incorrect.
   Two static routes needs to be added on R29.One to R29, other to R31

ouki 发表于 2011-10-1 02:24:00

wanzxj 发表于 2011-10-1 00:40 static/image/common/back.gif
TS3++ solution：

1) R15 cannot telnet R14 & R13 while sourcing loopacbk zero( fram relay question ...

谢谢！请问有拓图吗？

wanzxj 发表于 2011-10-1 18:47:25

本帖最后由 wanzxj 于 2011-10-1 18:48 编辑

ouki 发表于 2011-10-1 02:24 http://bbs.hh010.com/static/image/common/back.gif
谢谢！请问有拓图吗？

有！！！

dziwen 发表于 2011-10-1 20:37:46

真的还是假的
页: [1] 2 3 4
查看完整版本: Cisco出狠招-新版Lab和TS 考一个挂一个