CCNA LAB 97: Configuring Multilink PPP (MLPPP)
本帖最后由 小乔 于 2023-1-13 10:50 编辑Lab Objective
The objective of this lab exercise is for you to learn how to configure a Multilink PPP connection.
Lab Purpose:
MLPPP is a feature that will allow you to provide redundancy and some sort of load balancing by using two links (interfaces) and the benefits of the encapsulation protocol of PPP. As a Cisco engineer, as well as in the Cisco CCNA exam, you will be expected to know how to implement MLPPP functionality.
Certification Level:
This lab is suitable for ICND2 and CCNA certification exam preparation.
Lab Difficulty:
This lab has a difficulty rating of 7/10.
Readiness Assessment:
When you are ready for your certification exam, you should complete this lab in no more than 10 minutes.
Lab Topology:
Please use the following topology to complete this lab exercise:
Task 1:
Configure hostnames on R1 and R2 as illustrated in the topology.
Task 2:
Create a Multilink interface on R1 and R2 with the following settings:
Multilink group: 1
Encapsulation type: PPP
IP address: As in the diagram
Task 3:
Configure both Serial interfaces on R1 and R2 to join Multilink group 1.
Task 4:
Make sure that there is reachability between R1 and R2 via the MLPPP interface and that the interface is up and running.
Configuration and Verification
Task 1:
For reference information on configuring hostnames, please refer to earlier labs.
Task 2:
R1#conf t
Enter configuration commands, one per line.End with CTRL/Z.
R1(config)#int multilink 1
R1(config-if)#encapsulation ppp
R1(config-if)#ppp multilink group 1
R1(config-if)#no shutdown
R1(config-if)#ip add 192.168.10.1 255.255.255.252
R1(config-if)#end
R2(config)#int multilink 1
R2(config-if)#encapsulation ppp
R2(config-if)#ppp multilink group 1
R2(config-if)#no shutdown
R2(config-if)#ip add 192.168.10.2 255.255.255.252
R2(config-if)#end
Task 3:
R1#config t
Enter configuration commands, one per line.End with CTRL/Z.
R1(config)#int serial0/0
R1(config-if)#encapsulation ppp
R1(config-if)#ppp multilink group 1
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#int serial0/1
R1(config-if)#encapsulation ppp
R1(config-if)#ppp multilink group 1
R1(config-if)#no shutdown
R1(config-if)#exit
R2(config)#int serial0/0
R2(config-if)#encapsulation ppp
R2(config-if)#ppp multilink group 1
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#int serial0/1
R2(config-if)#encapsulation ppp
R2(config-if)#ppp multilink group 1
R2(config-if)#no shutdown
R2(config-if)#exit
Task 4:
R1#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Serial0/0 unassigned YES unset up up
Serial0/1 unassigned YES unset up up
Multilink1192.168.10.1YES manual up up
R2#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Serial0/0 unassigned YES unset up up
Serial0/1 unassigned YES unset up up
Multilink1192.168.10.2YES manual up up
R1#ping 192.168.10.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 56/67/96 ms
来源: CCNA LAB90: Configuring EIGRP for IPv6
来源: CCNA LAB 91: Configuring Back-to-Back Serial Connections
来源: CCNA LAB92: Verifying Cisco HDLC Encapsulation
来源: CCNA LAB 93: Configuring PPP Encapsulation
来源: CCNA LAB 94: PPP Authentication Using PAP
来源: CCNA LAB 95: PPP Authentication Using CHAP (Method #1)
来源: CCNA LAB 96: PPP Authentication Using CHAP (Method #2) 谢谢楼主分享！ 看看，谢谢！！！ 谢谢分享 {:6_267:}{:6_267:}{:6_267:}{:6_267:}
页:
[1]