4/5 台灣 桃園 350-401 Pass
一進考場，因為前幾題是術科，載入時，考場人員陪我等待3~4分鐘。
總題數 : 60，
學科有7、 8題，是題庫沒看過的；
術科是連續 6 題。
術科可以按TAB，也可以打問號，
已建好的Flow-Monitor名稱，
指令打一半可以按問號看到。
https://cdn.hh010.com/static/image/hrline/1.gif
第 1 題術科 - VRF
P.S:如鴻鵠論壇情報，原廠題目有點問題，
R11設定完靜態路由，SW11是Ping不到SW22的。
題目如下 :
All configurations on R11 are complete and communication between R11 and R22 is functional. Complete the configurations on R22 for the tasks below.
Task 1
Extend the Finance VRF between R11 and R22 using Tunnel 10.
Task 2
Complete the Finance VRF configuration on R22 and configure static routing so that traffic between VLAN 111 and VLAN 222 uses Tunnel 10 exclusively.
Note: Sw22 can be used to validate traffic flow.
https://cdn.hh010.com/static/image/hrline/1.gif
第 2 題術科 - CoPP，寫ACL允許OSPF、Telnet通過
OSPF is preconfigured on all routers.
Configure R10 and R30 to complete these tasks.
Task 1:
Modify the existing ACL on R10 so that OSPF routes are received from R20 and R30.
• The modification should only allow OSPF routes to pass.
• Do not remove any configuration from R10 to achieve this task.
Task 2:
Configure CoPP on R30 to achieve these results:
• Permit Telnet traffic from 192.168.24.0/24.
• Limit traffic to 8,000 bps.
• Discard additional packets.
https://cdn.hh010.com/static/image/hrline/1.gif
第 3 題術科 - Flexible NetFlow、SPAN、IP SLA
P.S : 已建好的Flow-Monitor名稱叫 : Monitor-FlowR1，指令打一半可以按問號看到。
The Operations team started configuring several monitoring activities. Complete the configurations for the tasks below.
1. Enable Flexible NetFlow on R1 E0/0 in both directions using the pre-configured flow monitor.
2. Configure the switch port analyzer on Sw1 and mirror all E0/1 traffic to interface E1/3 using session number 5.
3. Configure a basic IP SLA ICMP echo operation on R1 to ping PC1 every 60 seconds.
https://cdn.hh010.com/static/image/hrline/1.gif
第 4 題術科 - LACP的EtherChannel除錯、Spanning-tree Vlan Root Primary
Complete the tasks below by making changes to Sw10 only. No access is provided to Sw20 or Sw30.
Task 1
Sw30 is actively attempting to negotiate an 802.1 trunking EtherChannel with Sw10 using LACP, but the channel is not functional. Resolve the issues on Sw10.
Task 2
Modify the spanning tree configuration to ensure that Sw10 is always the root for
VLAN 20.
https://cdn.hh010.com/static/image/hrline/1.gif
第 5 題術科 - 用Address-family建立eBGP、宣告所有Loopback網段
eBGP is configured on R2 and R3. Configure R1 to complete these tasks.
1. Using the address-family command, configure eBGP according to the topology. Use Loopback 0 for the router-id.
遇到小狀況 :
一、建鄰指令 : remote-as TAB不出來，必須含-完整手打出來，才能Key進去。
二、宣告指令 : network指令只能進入Address-family之後，才有辦法TAB出來，
跟EVE-NG完全不一樣。
2. Advertise R1's Loopback 0, 10, and 20 networks to AS 20 and AS 30.
第二小題要注意Loopback的子網遮罩，
Loopback 10&20的遮罩跟Loopback 0不一樣 :
Loopback 0 - 10.1.1.1 255.255.255.255
Loopback 10 - 209.165.201.1 255.255.255.240
Loopback 20 - 209.165.201.20 255.255.255.240
宣告網段時，要注意可用的網段起始位置。
https://cdn.hh010.com/static/image/hrline/1.gif
第 6 題術科 - OSPF用Network指令建鄰，將Area40 Summary成/20的路由
OSPF is preconfigured on all devices except R30. Configure R30 to complete these tasks.
Task 1:
Configure OSPF according to the topology using these requirements:
• Use Process ID 10.
• Use Loopback1 for the Router ID.
• Advertise all networks into OSPF.
Use network statements under the OSPF process to accomplish this task.
Task 2:
• Configure a /20 summary route for Area 40.
( 注意起始為10.40.48.0，
指令 : area 40 range 10.40.48.0 255.255.240.0 )
• Advertise only Type 3 LSAs into Area 0.
恭喜恭喜 ~ 同為台灣人 讚
{:6_267:}{:6_267:}{:6_267:}{:6_267:}{:6_267:} 感謝大大分享資訊 {:6_267:} 恭喜
{:6_299:} {:6_290:} 厲害了 高高手 太強啦 太強了 超強的~~~ congratulation, can you share which version of question bank are you using for this Exam 350-401 ?
謝謝分享 恭喜樓主
页:
[1]
2